FT Mini Sportster Build

I'm trying to download the build plans. Just getting a HTTP 404 error. Any advice on offer?
Log In to reply

When you click on the link to get the plans it takes you to http://www.stonekap.net/ftplans/index.cgi, but the Mini Sportster is not in the list of plans.
Log In to reply

FT,
I’ve built the FT Mini Sportster. I have all the parts but the motor. Do you have a recommended site to buy the EMAX 2004 size / 2200kv motor? I’m unable to find that exact motor. Is it safe to use a EMAX 2004 / 2300kv motor? This is the current parts I have:
1x Propellers 6 x 4
1 x 2S 7.4 800mAh 20C battery (E-flite)
1 x 15-Amp ESC 2-3 LiPo (Ares)
4 x 5g Servos

Log In to reply

This one would make a Great Biplane!
Log In to reply

Hoping to get the info regarding pre-painting soon.....

Thanks for great plans, articles and advise.
Log In to reply

Link to plans is bad!!! Looks like I'll have to pick a different plane to build. Hope it's back up soon!
Log In to reply

Thanks FT specialy for josh.you inspiring people to fly..you will be welcome in Bali.
Log In to reply

Can't wait to scratch build this plane, I'm going to use it as a stepping stone from my three channel planes into four channel planes like the Simple Storch. Thank you Flite Test :).
Log In to reply

where is the link for the paint advice that josh mentioned? I am still confused about the best time to minwax/pain. i was under the impression that the glue will not stick to minwax.
Log In to reply

How about plans for the pylons. Racing around trees or power poles can be unfriendly.
Log In to reply

http://www.stonekap.net/ftplans/FT%20Mini%20Sportster%20v1.0%20Full-Size.pdf


\
Log In to reply

Paint? What are you guys using? Brand/type? Spray paint? Seal it? I tried a large marker, looks like crap. Tried some spray paint I already had in shop, attacked foam......

IDEAS??? Pictures???
Log In to reply

WHERE IS THE PAINT INFO????? I RUINED MY NEW SCOUT MESSING WITH TRYING TO FINISH IT. If you can't amke these things look better guess I'm done building/flying them. I don't crash, and planes last for a long time, so I want it to look good.

So, what did you paint it with?

Was in poly coated, didn't look like it.

Please add link to paint/finish video.

Love my Scout, but it looks awful now after several failed finishing trials..........
Log In to reply

I have built and painted many FT aircraft, and I have applied Min wax oil based poly before building/gluing the plane together. I have never had a glue joint fail (except upon impact with the earth) but even then, the glue joints didn't fail.
1. Don't use aerosol poly, use the clear gloss (least amount of yellowing) from a can and work it into the paper using a foam applicator. Apply only enough to get the job done to save weight.
2. Let it dry COMPLETELY! This may take a few days. It will be dry to the touch, but all of the VOC's must completely evaporate out before applying glue. If there is still a fairly strong odor coming off the foam board, wait another day.
3. The foam board will now accept spray paint and low adhesion masking tape with no problems. Usually 2 light coats will get the job done.
I poly my kits as soon as they arrive and let them sit until I'm ready to build. It's really worth the extra effort. If you do this process and edge seal the open edges with poly or hot glue, you can belly land first thing in the morning on dew covered grass with no worries.
Log In to reply

The motor mount is installed reverse with the cut out for motor wire on the wrong side. Had to get the dremel and grind opening on left looking from the front. In the mini pod build video it is pointed out to check this out with the motor wires before you glue but I build my mount as shown on the mini sportster video. Too late. Does the other motor pack contain the motor used for the video?
Log In to reply

Where can I get the paint template for this design?
Log In to reply

Log In to reply